Leeson Sub-Micro Dynamic Braking Kit for Ext Resistor User Manual download pdf

SUB-MICRO SERIES DYNAMIC BRAKING OPTION (FOR USE WITH EXTERNAL RESISTORS)

INSTALLATION AND OPERATION INSTRUCTIONS

Manual Number: SDBN06C

(These instructions apply to Dynamic Braking modules 174417, 174418, and 174419 ONLY)

The Sub-Micro Series Dynamic Braking option can be used with all SM, SM-Plus, and SM-Basic models.

SM-PLUS SERIES DRIVES

PROGRAMMING

1. Set Parameter 09 (TB-31 OUTPUT) to DYNAMIC BRAKING (04).

WIRING

The diagram to the right illustrates how the DB module is wired to the SM-Plus Series

drive.

NOTE 1: Use 18 AWG wire for control connections.

NOTE 2: Use minimum 14 AWG wire for connections to B+, B-, R+, and R-. The B+

and B- wires MUST be twisted together and must be less than 12 inches

long. Twisting the R+ and R- wires is also recommended.

NOTE 3: External resistors are required when using Dynamic Braking modules 174417,

174418, and 174419. External resistor assemblies are available from LEESON

(refer to the resistor selection chart on the next page).

SM-PLUS

POWER

TERMINALS

SM-PLUS

CONTROL

TERMINALS

DB OPTION MODULE

312

GND

B - B + R + R -

B - B +

SM-PLUS DIAGRAM

EXTERNAL

RESISTORS

(SEE NOTE 3)

WARNING!

Remove power from the drive and wait three minutes before wiring the DB module. Incorrect wiring of the B+ and B- terminals will result in

equipment damage! The B+ terminal on the DB module must be connected to the B+ terminal on the Sub-Micro drive, and the B- terminal on the DB

module must be connected to the B- terminal on the Sub-Micro drive.

SM SERIES DRIVES

PROGRAMMING

1. Set Parameter 12 (TB-13E FUNCTION) to DYNAMIC BRAKING (20).

WIRING

The diagram to the right illustrates how the DB module is wired to the SM Series drive.

NOTE 1: Use 18 AWG wire for control connections.

NOTE 2: Use minimum 14 AWG wire for connections to B+, B-, R+, and R-. The B+

and B- wires MUST be twisted together and must be less than 12 inches

long. Twisting the R+ and R- wires is also recommended.

NOTE 3: External resistors are required when using Dynamic Braking modules 174417,

174418, and 174419. External resistor assemblies are available from LEESON

(refer to the resistor selection chart on the next page).

POWER

TERMINALS

CONTROL

TERMINALS

DB OPTION MODULE

13E

GND

B -

B +

R + R -

B - B +

SM DIAGRAM

EXTERNAL

RESISTORS

(SEE NOTE 3)

LEESON ElectricLEESON Electric

LEESON Electric • 2100 Washington St. • Grafton, WI 53024 • Ph: (262) 377-8810 • Fax: (262) 377-9025 • www.leeson.com

1 2

Summary of Contents

Page 1 - SM SERIES DRIVES

SUB-MICRO SERIES DYNAMIC BRAKING OPTION (FOR USE WITH EXTERNAL RESISTORS)INSTALLATION AND OPERATION INSTRUCTIONSManual Number: SDBN06C(These instructi

Page 2 - SM-BASIC DRIVES

4.06"2.00"GND4.6"FRONTVIEW3.1"3.1"SIDE VIEWHP 240 / 200 Vac 480 / 400 Vac 590 / 480 Vac0.25 - 0.5174178174179N / A1 - 1.51741

Comments to this Manuals

No comments

Leeson Sub-Micro Dynamic Braking Kit for Ext Resistor User Manual

Browse online or download User Manual for Software Leeson Sub-Micro Dynamic Braking Kit for Ext Resistor. LEESON Sub-Micro Dynamic Braking Kit for Ext Resistor User Manual [fr]

Summary of Contents

Comments to this Manuals

Related products and manuals for Software Leeson Sub-Micro Dynamic Braking Kit for Ext Resistor