Leeson Micro Series Quick Reference Guide User Manual download pdf

LEESON

Variable Speed AC Motor Drives

RUN 60.00 HZ

PROG

RUN

AUTO

MAN

START

ENTER

FWD

REV

STOP



Micro Series

Quick Reference Guide

NOTE: Before installing and operating the MICRO SERIES

drive, please read and become familiar with the MICRO SERIES

Installation and Operation Manual.

Adjustable Speed AC Motor Control

2 OUTPUT ACCEL

In the example above, the second fault is being viewed, which is

an OUTPUT fault that occurred while the drive was accelerating.

FAULT

NUMBER

FAULT

MESSAGE

DRIVE

STATUS

MICRO SERIES FAULT HISTORY

Parameter 70 — FAULT HISTORY stores the last eight faults that

tripped the drive. The FAULT HISTORY indicates the number of

the fault (number 1 is the most recent fault), the fault message,

and the status of the drive at the time of the fault. An example is

shown below:

FAULT DESCRIPTION

OUTPUT Output Transistor fault. Output current exceeded 200%.

May be ground fault or short circuit.

LO VOLTS Low DC Bus Voltage fault. DC bus voltage dropped below 60%

May be low line voltage.

HI VOLTS High DC Bus Voltage fault. DC Bus voltage exceeded 120%.

May be overhauling load .

HI TEMP High Temperature fault. Heatsink or ambient temperature

too high.

OVERLOAD Current Overload fault. Output current exceeded 100% for

too long. VFD may be undersized.

PWR TRAN Power Transient fault.

PWR SAG Power Sag fault: New control board installed. Perform

factory reset using Parameter 65.

LANGUAGE Language EEPROM fault.

EXTERNAL External fault: TB-130 activated (Parameter 50).

DB ERROR Dynamic Brake fault. DB Resistors overloaded.

CONTROL Control Board fault. New solfware installed. Perform factory

reset using Parameter 65.

INTERNAL Internal fault

INTERN (#) Internal fault.

MC3000 FAULT MESSAGES

PARAMETER FACTORY PARAMETER FACTORY

NO. NAME DEFAULT NO. NAME DAFAULT

0 LINE VOLTS AUTO

1 SPEED #1 20.00 Hz

2 SPEED #2 20.00 Hz

3 SPEED #3 20.00 Hz

4 SPEED #4 20.00 Hz

5 SKIP #1 .00 Hz

6 SKIP #2 .00 Hz

7 BAND WID 1.00 Hz

8 ACCEL 30.0 SEC

9 DECEL 30.0 SEC

10 MIN FRQ .50 Hz

11 MAX FRQ 60.00 Hz

12 DC BRAKE .0 VDC

13 DC TIME .0 SEC

14 DYN BRAKE OFF

16 CURRENT 180%

17 MOTOR OL 100%

18 BASE 60.00 Hz

19 FX BOOST (NOTE 1)

20 AC BOOST .0%

21 SLIP COMP .0%

22 TORQUE CONSTANT

23 CARRIER 2.5 kHz

25 START NORMAL

26 STOP COAST

27 ROTATION FORWARD

28 AUTO/MAN BOTH

29 MANUAL KEYPAD

30 CONTROL LOCAL

31 UNITS HERTZ

32 HZ MULT 1

33 UNITS DP XXXX

34 LOAD MLT 100%

35 CONTRAST HIGH

39 TB5 MIN .00 Hz

40 TB5 MAX 60.00 Hz

42 TB10A OUT NONE

43 @TB10A 60.00 Hz

44 TB10B OUT NONE

45 @TB10B 125%

47 TB13A NONE

48 TB13B NONE

49 TB13C NONE

50 TB13D FAULT

52 TB14 OUT NONE

53 TB15 OUT NONE

54 RELAY NONE

58 ADDRESS 30

61 PASSWORD 0019

63 SOFTWARE (NOTE 2)

64 MONITOR ON

65 PROGRAM RESET 60

66 HISTORY MAINTAIN

70 FAULT HIST. (NOTE 2)

NOTE 1: REFER TO THE MICRO SERIES MANUAL.

NOTE 2: THESE PARAMETERS ARE VIEW-ONLY.

MICRO SERIES PARAMETERS

Micro Series

Intelligent Drive

Digital

LEESON SPEEDMASTER

BULLETIN #2452 3/98

1 2

Summary of Contents

Page 1 - Quick Reference Guide

LEESONVariable Speed AC Motor DrivesRUN 60.00 HZPROGRUNAUTOMANSTARTENTERFWDREVSTOPMicro SeriesQuick Reference GuideNOTE: Before installing and opera

Page 2 - MICRO SERIES KEYPAD

STOP 20.00 HZPROGRUNAUTOMANSTARTENTERFWDREVSTOPPress the START key to start the drive. The START keyis only active in LOCAL mode.PROGRAMMING THE MIC

Comments to this Manuals

No comments

Leeson Micro Series Quick Reference Guide User Manual

Browse online or download User Manual for Software Leeson Micro Series Quick Reference Guide. LEESON Micro Series Quick Reference Guide User Manual [fr]

Summary of Contents

Comments to this Manuals

Related products and manuals for Software Leeson Micro Series Quick Reference Guide